Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateTrusted Garage Door Repair for Evergreen Homeowners
When your garage door stops lifting, starts grinding, or refuses to close all the way, you need a specialist who knows exactly what they’re looking at. That’s what we do at Ashton Garage Door Repair. Since 2013, Tom Lund and our team have repaired doors and openers across Evergreen, from the neighborhoods east of Highway 101 to the streets around Lake Cunningham. A typical repair in this area runs $150 – $600, and we send a technician fast, Sunday through Friday, 7am to 7pm. Call (833) 400-0995, and we’ll walk you through what’s happening with your door and get a technician on the way. We answer 24/7.
We’re a focused garage door specialist, not a generalist handyman. That matters when your door is stuck and you need someone who has seen this exact failure before. Whether you have a Wayne Dalton door with a Chamberlain opener or a Raynor system with a Genie drive, one call covers the whole door.
Garage Door Spring Repair
Garage Door Spring Repair is the most common job we do in Evergreen, and it usually costs $180 – $340 for one spring. A matched pair is typically replaced together, so expect about twice that range for both. Springs carry the full weight of your door, and when one breaks, your door either won’t lift or slams down hard. We work on torsion and extension springs across all major brands, including Clopay and Amarr, and we always set the final price in a written estimate before any work begins.
What Happens When a Spring Breaks
You’ll usually hear a loud bang from the garage, like a firecracker. Then the door will feel impossibly heavy to lift manually. If you try to run the opener, you risk burning out the motor, so it’s better to stop and call us.
Why We Replace Springs in Pairs
Most doors use two springs, and they wear at roughly the same rate. When one fails, the other is usually close behind. Replacing both at once restores balance and keeps the door from working the opener too hard.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Garage Door Sensor Repair
Garage Door Sensor Repair fixes the small photo-eye units near the bottom of your door tracks that keep the door from closing on people, pets, or cars. When these misalign or fail, the door reverses right after hitting the floor or refuses to close at all. This repair typically falls inside our $150 – $600 garage door repair range and is often resolved in one visit. We test for wiring issues, alignment problems, and signal interference before recommending any replacement parts.
Common Sensor Failures
Loose brackets, sun glare, and dirty lenses cause most sensor problems. We realign the lenses, clean them properly, and check the wiring back to the opener. Sometimes the sensor itself is dead and needs replacing.
Sensor Repair or Opener Problem?
It’s easy to confuse a bad sensor with a faulty opener logic board. We test both before quoting, so you don’t pay for a board when a $15 bracket was the real issue. From the spring to the smart opener, we fix the whole system.
Emergency Garage Door Repair
Emergency Garage Door Repair covers the times when your door is stuck open, your car is trapped inside, or the door came off its tracks and you can’t secure your home. These jobs usually land in the $150 – $600 range, and we treat them as priority calls. Call (833) 400-0995 and we’ll dispatch a technician fast, Sunday through Friday, from 7am to 7pm. We answer 24/7, so you’ll always reach a person.
What Counts as an Emergency
A door that won’t close is a security issue. A door that won’t open traps your car. A door hanging from one cable is dangerous. If your door is doing something you wouldn’t want a neighbor to see, call us now.
How We Handle Urgent Calls
Our technician arrives with enough common parts on the truck to handle most single-visit repairs. We give you the written estimate before any work starts, then get your door operating again. If a part is unusual, we’ll secure the door so it can’t fall and schedule the follow-up quickly.
Garage Door Panel Replacement
Garage Door Panel Replacement fixes dented, cracked, or rusted sections without replacing the entire door. In Evergreen, we typically see panel damage from bikes, basketballs, or the occasional delivery truck, and a single panel replacement runs $250 – $500. We match the existing door’s style and color as closely as the manufacturer allows. If your door is older and panels are no longer made, we’ll tell you honestly whether replacement makes more sense.
When a Panel Can Be Matched
Clopay, Amarr, and Wayne Dalton all sell replacement sections for many of their current models. If your door is manufactured and still in production, we can usually order the right panel and install it within a week or two.
When Replacement Is Smarter
Multiple damaged panels or a door near the end of its service life often cost more to patch than replace. We’ll quote both options and let you decide. Repair or replace – we’ll tell you which one actually makes sense.
Garage Door Maintenance
Garage Door Maintenance is the scheduled tune-up that keeps your door quiet, balanced, and safe. Most Evergreen homeowners should have this done every 12 to 18 months. A maintenance visit typically runs $150 – $300 depending on what needs adjusting, and it catches small problems before they become $600 repairs. We inspect, lubricate, adjust, and test every moving part on your door and opener.
What a Tune-Up Includes
We check spring tension, cable condition, roller wear, track alignment, sensor function, and opener force settings. Then we lubricate hinges, rollers, and bearings with the right garage-door grease, not WD-40. Finally, we run a full open-and-close cycle and listen for anything off.
Why Evergreen Homes Benefit Year-Round
Even with mild winters, garage doors pick up dust and lose lubrication in our dry summers. Parts wear from daily use, not just weather. A yearly check keeps a 7-foot door gliding like it did when it was installed.
Garage Door Roller Replacement
Garage Door Roller Replacement is what quiets a door that rumbles, shakes, or screeches as it moves. Rollers wear out every 5 to 10 years, and replacing a full set of 10 to 12 rollers usually costs $110 – $220 in this area. We replace nylon and steel rollers on every brand we service, including Raynor and Clopay doors. New rollers reduce strain on your opener and extend the life of your tracks.
Signs Your Rollers Are Worn
A door that shudders on the way up or makes a grinding noise usually has flat-spotted or seized rollers. You might also see metal shavings on the track or notice one side of the door lifting slightly before the other.
Nylon vs. Steel Rollers
We explain the difference and help you choose. Nylon rollers run quieter and are gentler on tracks. Steel rollers last longer but need more lubrication. We’ll base the recommendation on how often you use the door and how much noise you’re willing to accept.
Commercial Garage Door Repair
Commercial Garage Door Repair keeps your loading dock, warehouse, or shop door running when it has to work every single day. We repair sectional, rolling steel, and high-lift doors throughout the Evergreen industrial corridors. Commercial repairs start at $150 and scale with the size and complexity of the door, and every job gets a written estimate first. Same-day service is available for businesses that can’t wait.
Downtime Costs Money
A stuck dock door stops your whole operation. We prioritize commercial calls and send a technician fast, Sunday through Friday, from 7am to 7pm. We answer 24/7, so you can report the problem the moment it happens and get on the schedule immediately.
What We Handle on Commercial Doors
We repair springs, cables, openers, safety systems, and track damage on commercial doors. If your door is beyond repair, we can quote and install a replacement built for commercial duty cycles. One company handles the entire job from diagnosis to install.
Garage Door Cable Repair
Garage Door Cable Repair fixes the braided steel cables that work with your springs to lift the door. A snapped or frayed cable usually costs $130 – $250 to replace. Cables are under extreme tension when the door is down, and a broken one leaves the door uneven and dangerous. We never recommend that a homeowner attempt this repair themselves. The risk of a cable whipping loose is real, and the door can drop without warning.
Spotting Cable Trouble Early
Look for fraying near the bottom bracket or rust along the cable length. A door that hangs slightly crooked is another sign one cable is failing. If your door squeaks or groans when it moves, a worn cable could be rubbing against the drum.
What a Cable Repair Involves
We remove all tension from the springs first, then replace the bad cable with the correct diameter and length for your door. We check the drums and bottom brackets while we’re there. The whole job usually takes under an hour, and we’ll test the door several times before we leave.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service LiftMaster openers every week, and we know their models from the basic chain-drive units to smart openers with Wi-Fi and battery backup. If your LiftMaster won’t respond to the remote or the wall console, we can usually diagnose it in one trip.
We also handle Wayne Dalton doors and their TorqueMaster spring systems, which many generalist repair companies won’t touch. And we work on Craftsman openers, including older models where parts are getting harder to find. Whether you have a Wayne Dalton door with a Craftsman opener or any other make, we can help.
Signs You Need a Pro Right Now
- Your door won’t close all the way. This is the most common sign of a sensor issue or a broken spring. A door that sits open even an inch is an invitation to pests and a security risk. Call us before you leave for work.
- You hear a loud bang from the garage. That’s almost always a spring breaking. The door will feel impossibly heavy after this. Do not try to open it manually – call us instead.
- The door shakes or jerks while opening. Usually a worn roller, a cable issue, or a track problem. Continuing to use it will damage the opener and could pull the door off its tracks.
- The opener hums but the door doesn’t move. The motor is running but the gear is stripped, the belt is broken, or the door is stuck. Running the opener like this will burn out the motor completely.
- One cable is dangling or frayed. The cable is under high tension, and if it lets go it can whip and cause serious injury. Leave the door alone and call a professional immediately.
Our Process, Step by Step
- 1
You call us. When you call (833) 400-0995, a real person answers, not a phone tree. We ask what the door is doing and gather the details our technician needs before leaving the shop. We answer 24/7.
- 2
We diagnose on site. The technician arrives, inspects the door and opener, and explains exactly what’s wrong in plain language. We give you the written estimate before any work starts, and the price we quote is the price you pay.
- 3
We repair with the right parts. We carry common springs, cables, rollers, and sensors on the truck so most repairs are finished that day. If we need a special part, we order it and get you back on the schedule fast.
- 4
We test everything. After the repair, we run a full cycle, check balance, adjust the opener force settings, and make sure the safety sensors work. We don’t leave until the door moves smoothly and quietly.
- 5
We tell you how to keep it running. We’ll point out anything that’s wearing and give you a straight answer on whether it should be replaced now or can wait. No upsell, just what we’d do on our own door.
How Much Does Garage Door Repair Cost in Evergreen?
A typical garage door repair in Evergreen costs $150 – $600, depending on what’s wrong. Spring replacement is the most common repair at $180 – $340 for one spring. Sensor problems and cable work usually land between $130 and $250. Roller replacement runs $110 – $220. When multiple parts have worn out together, you’re looking at the higher end of that range.
Several things affect your final price: the weight and size of your door, the brand of parts needed, and how many components have failed. The written estimate sets the final price, so you’ll know the number before we turn a single wrench. Never accept a quote over the phone without an inspection, and don’t pay surge pricing for an emergency call. Our estimate is free, and there’s no service-call fee.
To avoid overpaying, get a full diagnosis rather than a symptom-based patch. A door that’s noisy might need rollers now and springs soon. We’ll tell you what’s urgent and what can wait. For an exact quote on your door, call (833) 400-0995. We answer 24/7.
Our Service Area Near Evergreen
From Evergreen, we cover the surrounding neighborhoods and cities without long waits. We regularly send technicians to garage door repair jobs in Silver Creek Country Club, East San Jose, North San Jose, and South San Jose. We also serve Milpitas, Santa Clara, Sunnyvale, Campbell, Cupertino, West San Jose, and Morgan Hill. Fast dispatch from 7am to 7pm, Sunday through Friday, means most Evergreen calls get same-day service.
Serving Evergreen, CA – Our Local Coverage Area
We serve Evergreen and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Repair in Evergreen
Garage door repair is the process of diagnosing and fixing any component of your garage door system, including springs, cables, rollers, tracks, panels, sensors, and openers. In Evergreen, we handle everything from a snapped spring to a door that came off its tracks. The goal is a door that opens and closes smoothly, safely, and quietly, and we always quote the full price before starting.
Most common repairs, like spring replacement or sensor realignment, take under an hour once the technician arrives. More involved jobs, like panel replacement or track realignment, can run two to three hours. We carry the most common parts on the truck so we can finish the job in one trip.
Typical repairs in Evergreen run $150 – $600. A single spring replacement is $180 – $340, while a full panel replacement is $250 – $500. The only way to know your exact price is an inspection, which is free. We’ll give you a written estimate before any work begins.
Yes, we service LiftMaster openers, including smart models with Wi-Fi and battery backup. We also work on Chamberlain, Genie, and Craftsman openers, and doors from Clopay, Amarr, Wayne Dalton, and Raynor. Your door, your brand, our specialty.
Same-day service is available in most cases when you call before 3pm. We dispatch technicians fast, from 7am to 7pm, Sunday through Friday. We answer 24/7, so even if it’s late, call us and we’ll book you into the next dispatch opening.
We stand behind our repairs and the parts we install. Warranty length depends on the type of repair and the manufacturer of the parts used. We’ll explain exactly what’s covered before we start, and we’ll put it in writing.
Clear the area around the door so our technician has room to work safely. Park any cars outside the garage if possible, and unlock any side doors or gates. It helps to know your door’s brand and the age of your opener, but it’s not required. We’ll handle the rest.
Schedule Your Garage Door Repair Service in Evergreen Today
If your door is acting up, don’t wait for it to fail completely. Call (833) 400-0995 now for a free estimate. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. One call covers the whole door.
Written by Tom Lund, Owner at Ashton Garage Door Repair, serving Evergreen since 2013.